CGI Window Installation Nationwide | Sightline Windows & Doors North Miami

CGI Window Installation: The North Miami Owner’s Guide

CGI window installation in North Miami typically runs $340-$780 per opening for standard replacement, with most projects scheduled within 48-72 hours of the measured survey. We stock CGI-compatible hardware, glazing beads, and frame components for same-day repair on common failures. Most North Miami homeowners discover a problem when they feel salt-air draft around the sash, see condensation between impact-rated glass lites, or the window sticks during the humid months between May and October.

Call (786) 706-0468

Which CGI Models This Applies To

CGI builds several series that circulate through North Miami homes, and the part you need depends on which line is in your wall. The Estate Series uses a heavier aluminum frame with a distinct bulb-style glazing bead that presses in from the exterior; the Sentinel Series carries a slimmer profile with a snap-in vinyl bead that degrades faster in direct sun. The Targa Series, common in mid-2010s construction along the Biscayne corridor, uses a hybrid system: aluminum frame with a thermal break and a specific wedge-gasket arrangement that does not interchange with Estate or Sentinel hardware.

Check the etched mark in the glass corner or the stamped code on the frame edge, usually visible when you open the sash fully. If the label reads “ES” followed by a four-digit number, you have Estate Series. “SNT” indicates Sentinel. “TRG” or no prefix with a date code 2014-2019 likely means Targa. We carry OEM glazing beads and gaskets for all three lines, plus quality aftermarket equivalents where the original part is back-ordered. The aftermarket decision for CGI specifically hinges on the glazing stop geometry: an incorrect bead profile leaves a gap that passes water during a driving rain, and North Miami’s summer storms will find that gap.

One compatibility gotcha we see repeatedly: Targa Series windows from 2016-2018 used two different sill depths depending on whether the original order specified impact-rated or non-impact glass. The frame looks identical from the interior, but the glazing pocket depth differs by 3/16 inch. Measure the glass thickness at the edge, or call us with the etched code and we will pull the original spec.

Before

After

Signs Your CGI Window Installation Is Failing

• Draft at the sash meeting rail or frame perimeter. The compression seal has lost its memory, usually from UV exposure and the thermal cycling that North Miami’s coastal climate delivers year-round. Salt air accelerates the hardening; a seal that should flex to 40 percent compression becomes rigid and gaps open.
• Condensation between glass panes on impact-rated units. The edge seal on the insulated glass unit has failed, allowing moist outside air into the airspace. In CGI impact units, this is not a field-repairable condition; the entire glazed unit must be ordered to the original size and thickness.
• Window binds or requires force to open and close. The balance system or roller assembly has corroded, or the frame has shifted slightly in the rough opening. We see this often in 1980s-1990s North Miami concrete block construction where the original installation did not include proper shimming at the sill.
• Visible water staining on the interior sill after heavy rain. The weep holes are blocked with debris, or the sill flashing was omitted or improperly lapped during original installation. CGI frames have specific weep locations that must remain clear; a homeowner can check these, but flashing repair requires removing the unit.
• Glazing bead pulling away from the frame at corners. The vinyl or aluminum bead has aged beyond its elastic limit, or the original installer used an incorrect bead size for the glass thickness. This is the failure mode we catch most often during our documented photo surveys: a corner gap of even 1/8 inch will pass water under wind pressure.

Replacement Cost & What’s Included

For North Miami properties, our installed pricing for CGI window work breaks down as follows:

What drives the range: glass thickness and impact rating, frame condition behind the trim, and whether the original installation used proper flashing integration. Every quote we write in North Miami includes the measured survey you keep, the written scope with line-item parts and labor, and the documented photo record delivered at completion. The 365-Day Done Right Promise applies to all CGI work. We do not charge for revisiting a detail that was in our original scope.

DIY or Call Us?

There is safe checking, and there is work that belongs to a trained technician with the right tools.

A homeowner can verify: whether weep holes are clear, whether the glazing bead is fully seated at all corners, and whether the window operates smoothly without binding. Use a flashlight and a plastic putty knife, not metal. If you find a gap, photograph it; that image becomes useful documentation.

What goes wrong in DIY: removing a glazing bead from an impact-rated unit without supporting the glass risks dropping a 40-80 pound lite. The balance systems in CGI windows are under spring tension; improper release can damage the frame or cause injury. Re-glazing an impact unit requires setting blocks at specific locations to maintain structural certification; incorrect placement voids the rating and the warranty. We are background-checked, uniformed, and identified by license number before arrival, per Haven Clause 3. For CGI work in North Miami, call (786) 706-0468 and we will schedule the measured survey. The written price arrives before any tool is lifted.

FAQs